艳妇乳肉豪妇荡乳av无码福利,国人av一区二区三区啪啪,久久久婷婷婷五月亚洲综合色,国产免费一级片内射欧美妇,亚洲图片小说欧美另类
Welcome to the official website of the Taian Haishu Machinery Co., Ltd.,Service Phone:0086-0538-8606169ChineseEnglishSitemapEnterprise MailboxContact Us

Sale Of CNC Lathe

Senior Expert Of CNC Lathe

Global Service Hotline

0086-0538-8606169

Notice:
Warm congratulations "HAISHU" brand CNC machine tool exports reached 40 countries. They are: the United States, Britain, Germany, Sweden, Italy, Russia, Turkey, New Zealand, Colombia, South Korea, Bahrain, South Africa and other countries. "HAISHU" brand has been known at home and abroad.
Contact Us
Global Hotline:
+86-538-8606169

Taian Haishu Machinery Co.,Ltd.

Telephone: +86-538-8606169

Fax: +86-538-8606169

Address: Zhouwangzhuang Village, Shankou Town

             Taian City Shandong Province China

Current Location:Home Page » News » Company News
Introduction to the basic operating steps of spindle clearance adjustment explained by CNC lathe manufacturers
From:Taian Haishu Machinery Co.,Ltd. Updatetime:2023-7-11 16:51:11 Views:
For CNC lathes, there are certain standard requirements for the clearance between the spindles.

For CNC lathes, there are certain standard requirements for the clearance between the spindles. If it is too wide or too narrow, it can cause certain safety hazards to the operation of the lathe.

However, there must be some experience to support the operation of the spindle clearance, mainly because it is generally not necessary to stop the machine when operating the spindle clearance

The

requirements for operators are very high. Today, our CNC lathe manufacturer will explain the basic operating steps for spindle clearance adjustment.

The main shaft is a hollow stepped shaft, which

passes through the steel rod when using long bar material at the inner hole position and unloading the top. It can also be used for pneumatic, electric, and hydraulic clamping device mechanisms.

The taper hole of the front axle of the main shaft is 90mm, used for installing the top and front top points. Sometimes a spindle can also be installed, using the friction force matched by the cone

to directly drive the spindle and workpiece to rotate. The cone hole at the rear end of the spindle is the process hole.

For the clearance adjustment operation between the spindle of a CNC lathe, we

can roughly follow the following steps:

① Loosen the locking screw on the front nut first.

② Tighten the adjustment nut and move the inner ring to the right of the spindle cone. As the bearing

inner ring is thin and the inner hole is the same as the spindle cone, it has a 112 ° taper. Therefore, while the inner ring moves axially, it undergoes radial elastic expansion to adjust the

radial clearance or preload of the bearing. After the adjustment is completed, the screws on the nut are locked tightly.

The allowable deviation for radial and glaze runout of the main shaft is

00imrrJ. The radial runout of the CNC lathe spindle directly affects the roundness and concentricity of the machining surface, while the axial runout affects the flatness and pitch accuracy of the

machining end face. When the spindle runout exceeds the allowable value, simply adjust the front support clearance appropriately to adjust the spindle runout quantifier to within the allowable

value. If the radial runout does not meet the requirements, the rear bearing should be adjusted.

The front and rear supports of the CNC lathe spindle are lubricated by a lubricating oil pump, which

provides sufficient lubrication to the bearings through the oil inlet hole. At the same time, the heat generated by the bearings during operation is taken away. To avoid oil displacement, an oil

groove sealing mode is adopted at the front and rear support positions, with serrated circular grooves on the outer surface of the front nut and rear support sleeve. When the spindle of the CNC

lathe rotates, due to centrifugal force, the oil will be thrown along the inclined plane (towards the box) into the oil groove of the flange plate. The oil will flow through the return hole to the

bottom of the box, and then back to the oil pool in the left bed leg.

The above is the basic operation steps for spindle clearance adjustment explained by CNC lathe manufacturer Haishu Machinery,

hoping to be helpful for everyone in operating CNC lathes in the future.

  【Close】
News
Product

CNC lathe research and development, every problem we can not be ignored!

How to make my machine have a longer service life?

How to make the equipment have higher production efficiency?

How to ensure that the machine is simple to learn?

... ...

Learn CNC lathes

From the beginning our website!

Global Service Hotline:+86-0538-8606169

Service Center Contact Us
Message
Service
Common Question

Taian Haishu Machinery Co., Ltd.
Address:Zhouwangzhuang Village, Shankou Town Taian City Shandong Province China
Telephone:+86-538-8606169
Fax:+86-538-8606169
Copyright © 2015 HaiShu All rights reserved.
艳妇乳肉豪妇荡乳av无码福利,国人av一区二区三区啪啪,久久久婷婷婷五月亚洲综合色,国产免费一级片内射欧美妇,亚洲图片小说欧美另类